Plumbing Essentials: An Essential for Installing a Bathtub
Plumbing Essentials: An Essential for Installing a Bathtub
Blog Article
Listed here in the next paragraph you will discover a lot of superb resources with regards to Tools You Need to Install a New Bathtub .
Installing a tub isn't specifically brain surgery, however it does require strong plumbing, woodworking, and also often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably hard project. If the old tub is easily accessible, the project can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also place the new tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will require an assistant to leave the old tub and set in the brand-new one. See to it you have actually qualified yourself for the task and also are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is much better to take into consideration utilizing one before you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will certainly help you install a brand-new bathtub in your bathroom if you have actually currently purchased a brand-new tub and also don't need to change the arrangement of your previous water pipes.
Your devices as well as product checklist ought to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the restricted accessibility that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been eliminated, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing compound.
Before proceeding to fit the new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for minimizing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Safeguard the tap in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind must be linked to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the required position. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and also adjusting the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the various other faucet.
Turn on the water system and also inspect all joints as well as brand-new pipework for leaks and tighten them if needed. Load the bathtub and likewise examine the overflow electrical outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and securing around the bath tub must wait up until the bathtub has been used at least when as this will settle it right into its final position.
Planning for the Installment
First of all, the sustaining framework provided with the bathroom should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap includes a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a stiff seal, creating the water to pass through the wall between the bath as well as the tiling, leading to problems with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and fittings. They are sold in tubes and cartridges, as well as can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the tub with water prior to securing, to allow for the activity experienced when the tub remains in use. The sealer can break rather early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like reading about How to Install a Bathtub Yourself? Create a comment down below. We'd be pleased to hear your responses about this page. Hoping that you come back again before long. Appreciated our piece of writing? Please share it. Help others check it out. Thank you so much for your time invested reading it.
Get sorted, dial now! Report this page